Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
Listed here down the page you'll find a bunch of sensible guidance in relation to A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately hard job. If the old bathtub is conveniently accessible, the task can move easily; if you have to open up a wall surface to remove the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub and also set in the brand-new one. Ensure you have certified yourself for the task and fit attempting it. Instead of working with a contractor to take control of a halfway-completed project, it is better to take into consideration using one before you start. Opportunities are you might need an expert plumber to make tube connections.
This article will assist you set up a new bathtub in your washroom if you have currently gotten a brand-new bathtub and also do not need to change the setup of your previous supply of water pipelines.
Your devices as well as product list need to comprise the following:
Preparing for the Installment
Firstly, the supporting structure supplied with the bath needs to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, activate the faucets to drain any water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the limited access that is usually the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Using the two wood boards under its feet, put the tub in the needed setting. The wood boards are practical in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the tub until the level checks out level.
To mount faucets, fit all-time low of the furthest flexible tap connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water and examine all joints and also brand-new pipework for leakages and tighten them if essential. Load the tub and also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the bathtub has been utilized a minimum of once as this will certainly resolve it into its final position.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap as well as the sink. Protect the tap in place with the maker provided backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The previous type ought to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall in between the bath and also the tiling, causing difficulties with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components as well as installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can split rather early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads on Installing A Bathtub, I think sharing that excerpt was a good thing. Sharing is good. One never knows, you will be doing someone a favor. Thank-you for taking the time to read it.
Act, don't delay! Report this page